Ar barrel nut won’t come off

Saltwater60

Saltwater60

.950 JDJ
Messages
31,229
Reaction score
34,897
Location
Western NY
Having trouble getting the barrel nut off on my 6.8SPC barrel.
I’m installing a scope and a carbon fiber handgaurd. I’m using it for hunting and I want it to be fairly light. I read 35lbs/in for torque. This has to be way over that. There’s no gas block hole so it should have been torqued down to about 40 lbs/in imo. I’m going to hit it with some lube and let it sit until tomorrow. Never been fired so it can’t be gunned up. I got it to move a little bit in the wrong way and figured it would back off, but it’s not budging the other way at all. I checked and there’s no pins or anything.
 
Saltwater60

Saltwater60

.950 JDJ
Messages
31,229
Reaction score
34,897
Location
Western NY
Here’s some pictures
 

Attachments

  • 12CB2812-382B-41F2-82BD-E164A6AC6B62.jpeg
    12CB2812-382B-41F2-82BD-E164A6AC6B62.jpeg
    93 KB · Views: 26
  • 112E2144-D9C5-4F3F-ABD7-C8105D0DB92A.jpeg
    112E2144-D9C5-4F3F-ABD7-C8105D0DB92A.jpeg
    70.7 KB · Views: 27
cgrutt

cgrutt

.338 Win Mag
NYGF Vendor
Monthly Donor
Messages
8,877
Reaction score
16,721
Location
Interwebz
My first guess would be castle nut was staked to prevent it from coming loose. Dremel will reverse. Second guess would be thread locker. If they used blue it should come off with some persuasion. Red... well more persuasion and maybe a little heat lol.
 
Saltwater60

Saltwater60

.950 JDJ
Messages
31,229
Reaction score
34,897
Location
Western NY
I might just leave it. I was just going to swap to a different handguard. Might not be worth all this bs. The carbon fiber one isn’t that much lighter than the short aluminum handguard that’s on there now.
 
Jem45472

Jem45472

.308 Win
Messages
4,131
Reaction score
6,636
Location
Erie
If it's a non indexing barrel nut, I'd also guess they used red loktite. You could try putting some heat to it.
 
kev74

kev74

20×102mm Vulcan
Messages
45,565
Reaction score
143,696
Location
Orange Co.
Saltwater60 said:
I might just leave it. I was just going to swap to a different handguard. Might not be worth all this bs. The carbon fiber one isn’t that much lighter than the short aluminum handguard that’s on there now.
Click to expand...
That might be for the best. Aluminum can gall easily. You might be looking for a new upper if you try too hard loosening it.
 
Jem45472

Jem45472

.308 Win
Messages
4,131
Reaction score
6,636
Location
Erie
kev74 said:
That might be for the best. Aluminum can gall easily. You might be looking for a new upper if you try too hard loosening it.
Click to expand...
On second thought, I would have to agree with this. They should have used some type of grease to keep from galling the upper, and it shouldn't be that difficult to remove.
 
ArmedCorgi

ArmedCorgi

.475 A&M Magnum
Messages
14,425
Reaction score
22,648
Location
Utahardia
Stick it in the freezer for at least 30 minutes. Use a breaker bar. I had to do that when I changed uppers on my S&W sport. Barrel nut just would not break loose.
 
You must log in or register to reply here.
Top