So do other guns. Most run like champs. Even Keltecs do too. And no. Glock has never had the problems SIg has had. Brass to the face due to strong recoil springs and underpowered ammo or slides falling off during dry fire do not compare to firing when being dropped.
That wasn't a quality issue though. It was a poor design choice born of marketing.
I'm just replying to him saying that his Sigs run like champs. Most guns do except perhaps Diamondback, Rohrbaugh, or Seecamp that require only certain types of ammo to run without jamming.
About the only truly dangerous one listed there to me is the double feed one but if you follow the safety rules of the gun being pointed in a safe direction... Those problems were addressed, should have been fixed and were.If I were worried I would not continue on with my SIGS. Am I disappointed with the Drop test? Sure! but it will be fixed. I have tried to replicate the test myself and it took awhile (Many drops) to enact the trigger. As far as I'm concerned for it to happen all the stars must align meaning a perfect angle drop on the slide at 30 degrees. Once again I'm not to worried.
As far as Glock not having the problems as SIG has had? I don't know about that. You might want to look at the History of your platform.
1990 Upgrade Glock Model 19, 9mm Luger caliber, requires an upgrade for the following serial numbers: AN, BP, BR, BV, BW, BX, DL, DM, DN, DP, DR, DS, DT, DV, DW, DX, DY, DZ These pistols may have the potential of the action to malfunction as follows: 1. The slide locking back on a full magazine. 2. Failure to lock into battery because the barrel lug drags on the slide lock. 3. The magazine follower tips or sticks in the magazine tube. 1992, 6 part Upgrade GLOCK, INC. Technical Bulletin #920403
April 1, 1992 Glock, Inc. announces a production change of the firing pin safety system. This new firing pin safety system has been installed in all production Glock pistols since November, 1991. A voluntary upgrade is being offered to maintain the Glock tradition of ensuring that all of our pistols are up to the latest standards in 21st century Glock technology. Most importantly, the components of the new firing pin safety system are not interchangeable with the components of the old system and Glock will always strive towards maintaining this feature of interchangeably while working to ensure future interchangeably. The upgraded firing pin safety system consists of: the firing pin, firing pin safety, the extractor, the spring loaded bearing and the trigger bar. The upgraded system is applicable only to Glock pistols with the following serial number ranges : Glock 17 - alpha prefix AA - WF Glock 21 - alpha prefixes through XL Glock 19 - alpha prefixes through WJ Glock 22 - alpha prefixes through YA Glock 20 - alpha prefixes through WW Glock 23 - alpha prefixes through SK The upgraded firing pin safety has a new surface finish making it nearly 100% saltwater corrosion resistant. Also, after rigorous and extensive testing, the new system proves to be more durable and has a longer useful life. Here, as always, Glock is working toward maintaning its standard of perfection.
1993, G19 Upgrade Glock Model 19, 9mm Luger caliber, requires an upgrade for all pistols. These pistols have the potential for an UNINTENTIONAL DISCHARGE of a cartridge with the action open. The Glock model 19 pistol slide has a bottom protrusion, whose function is to push cartridges from the top of the magazine into the chamber. When the pistol is jammed in a double feed situation, the slide protrusion can come in contact with the primer of the jammed cartridge and cause UNINTENTIONAL DISCHARGE while the action is open. 2000, G26/27 Recoil spring upgrade Glock Model 26, 9mm caliber, serial numbers DGU, DHR DKU. Glock Model 27, .40S&W caliber, serial numbers DGD, DGV, DHS, DHT, DKV, DKW, DKX. Mr. Don Bulver, warranty department of Glock, Inc., indicated the recoil springs produced before September 1999 may shear off on some of these pistols due to over hardness of the support tube. Replacement springs will be distinguished by a vertical mark from the center on the front polymer portion of outer ring of the guide rod assembly, which will appear to be a mold line.
2002 Frame Upgrade – Rear slide rail The GLOCK Corporation has identified a problem with a very small percentage of GLOCK pistols produced between September of 2001 and May of 2002. The specific problem that has been identified is the potential of breaking a rear frame rail in pistols manufactured during this time period. Within the specific range the breakage rate has been less than 0.0188%. So, while the actual percentage of rails reported broken is within any accepted manufacturing tolerance, it is not an acceptable situation to the GLOCK Corporation. It is also important to note that under most conditions GLOCK pistols will continue to function with three rails. A routine maintenance check after each time the pistol has been taken out and used would immediately indicate if there is a problem. We are, therefore, concerned that a limited number of customers will not get the product we have promised them and what we have always delivered, the very best pistol on the market, in short, a GLOCK. For these reasons, we have made the decision that in the interest of customer service, replacement frames will be offered to anyone who has a firearm in this range and decides to take advantage of this offer. The replacement frames will have identical serial numbers to our customer's original firearm except the numeral 1 will be added as a prefix. If you believe your firearm is within this range, please call 1-866-225-4098 to take advantage of the ultimate in customer service. Nothing less than the best for our customers is acceptable to GLOCK and, as always, we will continue to work towards Perfection. It appears that only serial numbers starting with "E", "GSSF", or "USA" (American Hero’s Commemoratives) are affected. In general, the chronological serial number set that has the prefix letters of "EKA" through "EVR" inclusive appear to be the affected Glocks, regardless of caliber. Three letters precede three numbers on a plate forward of the trigger guard on the underside of the polymer frame. However, some aberrations to this generalization have been reported by GTers. Reports are that the affected Glocks were manufactured from September 2001 to May 2002. So if you bought (or won a GSSF Glock) an "E" or "USA" series Glock in September of 2001 up until the present day, you might have an affected Glock. Unfortunately, Glock has not published a list. Hope this helps, but again, if you are responsible enough to own a gun and can read this, you are smart enough to check for yourself by calling Glock.
August 8, 2005 - The Glock G36 issue Glock prides itself in the quality of its pistol and the quality of its manufacturing process. Despite our high standards, however, it has recently come to our attention through our quality testing efforts that a limited number of Glock Model 36 pistols may have an abnormality that could possibly interfere with the operation of the Glock trigger safety. The affected pistols require a simple but necessary modification to ensure the trigger safety operates as intended. IT IS ESSENTIAL FOR THE SAFE OPERATION OF YOUR GLOCK 36 THAT THIS MODIFICATION BE MADE AT GLOCK'S U.S. HEADQUARTERS IN SMYRNA, GA. If you possess a Glock Model 36 with a serial number in the ranges below PLEASE IMMEDIATELY UNLOAD THE FIREARM AND CLEAR THE CHAMBER. Deliver the pistol to : 1. A UPS Hub (not a store) 2. The place of business where you purchased the firearm of a dealer in your area with a daily UPS pick up.
I have not had a German made SIG, my 229 and former 226 ran just fine.
Well that's the way QC works, hit or miss. There are less stories of German P226 "misses" Functionally there is no difference at all between German and American made P226s beyond the American ones being a little heavier due to the milled stainless steel slides, as opposed to stamped carbon steel slides.
Why are you taking this personal? He is just saying that they handled it poorly.
