NO need for a case gauge.
Use the USPS flat rate method.
size the case.
plunk it in your barrel chamber.
"If it fits it ships" USPS
First batch of 45 ACP
- Thread starter RooftopKorean
- Start date
Use the USPS flat rate method.
size the case.
plunk it in your barrel chamber.
"If it fits it ships" USPS
.45 ACP, Head Spaces on the case mouth.......crimp 45 ACP at your own peril.
Crimp rounds,that have a flat rim, like 45 long colt, 45-70, etc.
Bottleneck cases, at your discretion.
If they slip past the chamber, you are fucked.
Crimp rounds,that have a flat rim, like 45 long colt, 45-70, etc.
Bottleneck cases, at your discretion.
If they slip past the chamber, you are fucked.
Far king
.357 mag
Far king
.357 mag
Ahh, quote feature in the fritz!!!!
repete
.338 Win Mag
Damn, this is getting confusing! 
Depick
.308 Win
Nice setup! I love the fact you have a dedicated room. That’s my hope for the next house. I want a dedicated gun room. I use a very similar recipe for my .45 acp load with HP-38.
Taper crimp for auto loaders, roll crimp for revolvers.
Thank you, if I can do it with limited space in a Brooklyn apartment you can do it where you are.
Shot some of my reloads and they worked fine. That being said, I was reloading some more yesterday night and found that three of my reloads had some of the copper jacket sheered slightly.
I did some Googling, found some suggested the mouth be widened slightly. I found it odd that my resizing die didn't do this. I used a tool with a rounded edge to widen the mouths on a couple of the brass slightly to see if it would resolve the issue, which it did.
Is there an actual reloading tool that would do this to make my life easier than me having to do this to 400 casings manually?
I obviously took apart those rounds and discarded the deformed bullets, reused the casings as they were undamaged.
I did some Googling, found some suggested the mouth be widened slightly. I found it odd that my resizing die didn't do this. I used a tool with a rounded edge to widen the mouths on a couple of the brass slightly to see if it would resolve the issue, which it did.
Is there an actual reloading tool that would do this to make my life easier than me having to do this to 400 casings manually?
I obviously took apart those rounds and discarded the deformed bullets, reused the casings as they were undamaged.
How does .45 ACP headspace? | [August Updated]
Contents How does .45 ACP headspace? The .45 ACP cartridge headspaces, or seats, on the case mouth. This means that the front end, or mouth, of the cartridge makes contact with the front end of the chamber, ensuring proper alignment and positioning for safe and reliable firing. 1. What is...
thegunzone.com
Headspace on Extractor?...that is a desperate situation to recommend, and not true, even if it may work with bad ammo that slips past the edge in the chamber.
Many extractors are modified for better extraction, not headspace and depend upon that chamber design.
read up.
Your expander die should be able to be adjusted to leave a slight bell on the case mouth that will accept a bullet without shaving the jacket while sizing the inside of the case. This more so needed when loading cast bullets. Your seating die should also size the outside of the case as well as put a slight taper crimp on the case mouth.
This will allow the cartridge to fit the chamber properly and headspace on the mouth of the case.
repete
.338 Win Mag
Turn the resizing die STEM in just a little bit and see what happens. I have the same problem because I don't segregate brass by head stamp nor do I trim them, that means they are different lengths thus some may get flared a lot some will be perfect and some may not get any flare at all. Watch what brand is shaving and pull them, if you get a lot of them then run a batch of just those.
Xae289
.223 Rem
So if you're using a Lee 4-die set, your 2nd die the expander/powder-thru die is what you use to set how much you bell your case mouth. If you're shaving copper jacket, you should bell your cases more. With the Lee expander die, all you need to do is turn it in until you have enough bell that the bullet is sitting on a barely noticeable flare on the case mouth. Other brand dies should have a similar ability to adjust how much you bell the mouth.
As far as crimp, yes, I think crimping is beneficial for most situations. For one, if you over-bell the mouth, crimping can fix it. Two, it helps secure the bullet in place so you won't get bullet set-back when chambering, unloading, and re-chambering a round. In a revolver, it resists bullet-pulling under heavy recoil.
A Lee factory crimp die is a very good tool. It not only makes it very hard to over-crimp and buckle a case, but also has a carbide ring that final sizes the loaded cartridge to squeeze it back into spec.
A taper crimp is the proper crimp for a semi-auto cartridge. It won't roll the case mouth in like a roll crimp, so it is still able to headspace on the case mouth.
Well @Xae289 and others have said, I forgot to use the expanding die... Now I feel stupid.
Expanded all my remaining clean brass, primed, charged, and loaded all of them.
Amazon delivered my Lee crimp die. I ran all 300 rounds I made today through the crimp die, worked like a charm.
Expanded all my remaining clean brass, primed, charged, and loaded all of them.
Amazon delivered my Lee crimp die. I ran all 300 rounds I made today through the crimp die, worked like a charm.
Huh? Why do you say that.
Last edited:
loading pistol cases on a single stage press is slavery.
I have a progressive press already. As I stated earlier I like to do first time loads of a new caliber I am loading on a single stage first for the first batch.
I got bored
Depick
.308 Win
I love reloading pistol rounds on my Rock Chucker.