Ultrasonic Cleaning Fluid?

[GTN]

I would like to use my ultrasonic cleaner for some gun parts like pistol barrels and other small parts, rifle bolt carriers etc…
I looked at Amazon and there are so many different options.
What cleaner fluid do you recommend?

 

[PA Guns & Ammo]

I have used powdered laundry detergent with very good results.

 

[GTN]

I have used powdered laundry detergent with very good results.

It doesn’t hurt the finish?

 

[spat]

I would like to use my ultrasonic cleaner for some gun parts like pistol barrels and other small parts, rifle bolt carriers etc…
I looked at Amazon and there are so many different options.
What cleaner fluid do you recommend?

Anything that works well for manual cleaning, isn't *too* flammable, and has a low viscosity.

It really depends on what material you are cleaning. Alkaline solutions work great on steel, avoid then on aluminum for instance.

I've used the generic harbor freight ultrasonic cleaner on steel and titanium pretty well. Not sure I'd use it on aluminum, or at least not for long.

 

[Saltwater60]

Anything that works well for manual cleaning, isn't *too* flammable, and has a low viscosity.

It really depends on what material you are cleaning. Alkaline solutions work great on steel, avoid then on aluminum for instance.

I've used the generic harbor freight ultrasonic cleaner on steel and titanium pretty well. Not sure I'd use it on aluminum, or at least not for long.

Why not too flammable? That could be fun!!

 

[spat]

Why not too flammable? That could be fun!!

Exciting anyway.

Might be fun outdoors

My main concern would be volatilizing the solvent with the ultrasound so you end up with a lot more of it in the air than you'd think you'd have.

 

[dsdmmat]

I use simple green in mine.

 

[FP1201]

Glad folks are giving advise on what to use....I have one of the Hornady US cleaners and have only used the Hornady solution, but that's getting pretty funky from gun parts.
Simple Green sounds good...
I wonder about odor free mineral spirits?
In the past Lacquer thinner was my go-to for cleaning Gun Parts encrusted with dried/sticky oils that had turned to varnish...does a great job cleaning and your Liver readily absorbs it through the skin (Osmosis) frikk'n wonder I'm alive at all.
We used to get 55 gallon Drums of "Zero-Tri" and that stuff worked great. but was wicked expensive.

 

[Darth]

Dawn Dish Soap

 

[GTN]

Dawn Dish Soap

Never would have thought that would be good. Just a few drops should be good?
Thanks

 

[Darth]

Never would have thought that would be good. Just a few drops should be good?
Thanks

If it's good rough for the little oil thief birds, it's good enough for my needs.

It's what I use.

 

[JunkBoxFull]

@GTN
I use liquid laundry detergent. I`ve had the very best luck with "ALL" and "PERSIL".
Its best to use distilled water too, in my own opinion.

Look into this link, it might shed some light on UltraSonic cleaning for you.

What do you put in a ultrasonic cleaner

Ultrasonic cleaners are invaluable tools for maintaining cleanliness and prolonging the lifespan of various items, ranging from jewelry to delicate instruments. By using ultrasonic waves to create tiny cavitation bubbles, these cleaners effectively remove dirt, grease, and other contaminants...

www.bjultrasonic.com

 

[Tisto]

Diesel fuel cleans almost anything metal.

 

[camper4lyfe]

One thing you can also do, if you have small parts, you can use something like a mason jar filled with cleaner and put that in the sonic filled with water. It'll work through the jar, and you won't have to chase parts.

 

[GTN]

I tried the dawn dish soap today. 12 min. It did an ok job. Maybe my bolt was just really dirty