cant get my rifle to cycle

H

holdover

.475 A&M Magnum
Messages
16,845
Reaction score
24,919
Location
occupied NY
My first build, and I thought I did a decent job, until I went to the range to fire it. one shot, no kills. no cycling of the next round. I had bought a a Odin works adjustable gas port. I tried fiddling with the adjustment and nothing ,then I lost the adjustment knob when i fired it and I said fuck that fancy shit ,just get me one that works, SO I bought a bravo co. gas block .I shot a blank through it and it wont cycle again. How hard can it be to line it up? So anyways Im kind of out of ideas

I have an 18 inch barrel . 0.75 the odin works went on no problem the Bravo company was super tight , Had to tap it in . I have them both flush to the ""gasport stop""? on the barrel . Now I cant see the actual hole to line it up visually , but I was considering tapping it back a pinch and see what happens . Anyone in western New York that can help me out ?
 
spat

spat

.950 JDJ
Messages
30,211
Reaction score
63,818
Location
Formerly Geneseo, NY. Now free in AZ
holdover said:
My first build, and I thought I did a decent job, until I went to the range to fire it. one shot, no kills. no cycling of the next round. I had bought a a Odin works adjustable gas port. I tried fiddling with the adjustment and nothing ,then I lost the adjustment knob when i fired it and I said fuck that fancy shit ,just get me one that works, SO I bought a bravo co. gas block .I shot a blank through it and it wont cycle again. How hard can it be to line it up? So anyways Im kind of out of ideas

I have an 18 inch barrel . 0.75 the odin works went on no problem the Bravo company was super tight , Had to tap it in . I have them both flush to the ""gasport stop""? on the barrel . Now I cant see the actual hole to line it up visually , but I was considering tapping it back a pinch and see what happens . Anyone in western New York that can help me out ?
Click to expand...
I wonder if you can just use some compressed air to see how well it's lined up ?

Remove the gas tube, close the bolt with an empty case in it to seal the breach, and then use a rubber tipped blow gun with an air compressor on the muzzle and see how much air you get out of the gas block ?

1600446711845.png
 
1075tech

1075tech

.338 Win Mag
Messages
7,165
Reaction score
17,486
Location
Escaped NY
One trick I've used to insure the port is lined up with the gas block is to use a short piece of uncooked spaghetti. Place a short piece in the inlet of the gas block, turned upside down. Slide the gb on the barrel and turn upright. The spaghetti will drop into the barrel when it's lined up with port. You can use a cleaning rod to break that and drop it from the barrel.
 
H

holdover

.475 A&M Magnum
Messages
16,845
Reaction score
24,919
Location
occupied NY
At this point. Im willing to pay someone have someone install it . any gunsmiths on this forum in WNY?
 
Mosinitis

Mosinitis

.338 Win Mag
Messages
8,529
Reaction score
7,918
Location
NY state
Some gas blocks don't index off the barrel shoulder, depends on gas block and how the barrel is machined. You can check for that by measuring a space to the gas hole on both parts before installing. If your gas block has a flat top surface, you can use a small lever on gas block and flat top of the receiver to align the gas block. You can also use a bore scope to check from inside the bore if the two holes are aligned. It's not too difficult, you just have to approach it methodically.
 
cgrutt

cgrutt

.338 Win Mag
NYGF Vendor
Monthly Donor
Messages
8,996
Reaction score
17,046
Location
Interwebz
I built a 6.8 SPC and it had trouble cycling first rounds. It started running fine after a couple boxes of ammo. May need some breaking in?
 
Airborneguy

Airborneguy

.338 Win Mag
LEO / LEA
Messages
6,559
Reaction score
12,826
Location
Staten Island
My AR-10 build (that I wanted to hunt with this season), if giving me the same problems. I'm most likely going to completely strip the upper and start again.
 
You must log in or register to reply here.
Top