PA Guns & Ammo
.45 acp
Where are you guys getting your non threaded ar15 barrels from besides Palmetto? Doing a custom build on a Fightlite SCR receiver and I need one to be NY compliant.
.750 non-threaded AR15 barrels? Where?
- Thread starter PA Guns & Ammo
- Start date
Newguyhere
.40 S&W
I built an SCR using a Ballistic Advantage.
Green mountain barrels has a 19 inch 1-6 twist non threaded
Login
www.gmriflebarrel.com
PA Guns & Ammo
.45 acp
How many rounds did you put through it? Green Mountain barrels from what I have read have been sub-par.
PA Guns & Ammo
.45 acp
I went to their website and looked through all the 223 Wylde and 5.56 barrels and they are all threaded.
I have put a few hundred through both of the guns with this barrel installed and am very pleased with the sub MOA performance.
You can also order a barrel from McGowen precision barrels
PA Guns & Ammo
.45 acp
This is going to be a shooter so standard AR15 barrels would suffice. Not looking to spend that much on a barrel but thanks for the info.
Vapor
.308 Win
If it's a cheap shooter, BCA may suffice.
I bet JSE surplus has some YHM barrels. My YHM 20" non threaded has been great.
I bet JSE surplus has some YHM barrels. My YHM 20" non threaded has been great.
PA Guns & Ammo
.45 acp
I looked on their page and the only non threaded barrels they have are bull barrels and I do not want a bull barrel.
PA Guns & Ammo
.45 acp
I want a 16" barrel and the money I spend on shipping it to you and having you do the work is not worth the money to invest into a cheap barrel. I will find one. Worst case scenario, I will just buy a normal barrel and pin and weld a thread protector on it myself but I rather have the look of a non threaded barrel. Thanks for the offer though.
meketrefe
.450/400 Nitro Ex
16.5" OL or 16" measured from the shank? you want at least a midlength porting job.
This is a good way to go IMO... Match Grade Barrel | .223 Wylde | Urban Super Sniper | 18"-https://shopwilsoncombat.com/
Also Lothar walter will cut you one very nicely polygonal and not cheap but also not too expensive.
you can also get a 18" stoner (very well priced through midway ) that are douglas barrels and just have it cut and crowned that is
a very quick job.
If the threads are 5/8 why not stick a pinned sleeve? if well done one cannot tell the difference (flush with the barrel)
and it is actually better than crowning for several reasons.
No need to weld anything. A blind pin on the actual join (not the threads like some hack gunsmiths do) is a permanent way
of doing it w/o screwing with the minor diameter of the barrel.
Last edited:
PA Guns & Ammo
.45 acp
I do not want a heavy or a bull barrel. This gun is just for fun and I do not need sub moa results. If I were to build and actual target gun, it will be on an AR platform and not on a SCR lower.
meketrefe
.450/400 Nitro Ex
It is not a heavy barrel it is a medium profile and they also have it fluted.
The 18 "douglas-stoner is also light enough and cutting threads and crowning is a 15min task in the lathe.
Bull barrels donnot make an ar more accurate, they mught mAke it worse because the biggest weakness is not the barrel but the receiver itself.
The 18 "douglas-stoner is also light enough and cutting threads and crowning is a 15min task in the lathe.
Bull barrels donnot make an ar more accurate, they mught mAke it worse because the biggest weakness is not the barrel but the receiver itself.
