96coal449
.308 Win
Your doing a great job! I see pride ..... pride is good .....
Finally collected everything I need to reload....
- Thread starter Wildman1024
- Start date
Wildman1024
.357 mag
Thanks.
Did you buy a stuck case tool. It's the best 20 buck you'll ever spend reloading.
RCBS Stuck Case Remover Kit https://www.amazon.com/dp/B000O7D5O2/ref=cm_sw_r_cp_apa_zPPPAb4H9PM7G
RCBS Stuck Case Remover Kit https://www.amazon.com/dp/B000O7D5O2/ref=cm_sw_r_cp_apa_zPPPAb4H9PM7G
Robin
.577 Tyrannosaur.
I use Varget in my 8mm, flows nice and for me very consistent and accurate loads. My son got two deer with them this year. Good luck!!!!
Robin
Robin
Joe Blow
.45 acp
Brass prep, in my opinion, is a pain in the ass. I've reloaded .223 for practice and competition at all levels. I started out doing the brass prep myself and it didn't take long before I said fuck this. I found a guy in WV who does full brass preparation. He's one of the top shooters in the country and knows his stuff. Last I saw for .223 he was getting $.045 per round (commercial or military) with a minimum of 2K rounds per order (he also does .308). Case prep includes:
Tumbled to high polish
Sized to SAAMI specs
Primer pockets cleaned
Flash hole deburred
Trimmed to standard specs
Case necks deburred and chamfered
Military crimp removed (swaged)
Cases are head spaced on a per customer basis using customer provided factory spent brass.
USPS priority mail flat rate shipping both ways. When it comes back it is gorgeous. Sit in the chair and prime away and yer ready for powder and press. I've loaded tons of this (mainly 69, 77, and 80gr. for competition and 55gr for the pistols).
Factoring in the cost of the brass prep tools, my time, etc., well worth it to me.
SmallGameAddict
.308 Win
Is Varget a ball powder? I was thinking of using it in my 7mm-08, and I like smooth dispensing from a powder measure.
I don't disagree with you but for me I like to drink and work at the bench. So to me I do brass prep all winter long. Now I will admit I probably don't shoot as much rifle as you alluded to.
Robin
.577 Tyrannosaur.
I call them kegs, you don't get a lot of chopping, and fairly consistent from throw to throw.
Robin
SmallGameAddict
.308 Win
So it's an extruded powder but flows well. Hmmm...
Thanks for replying. Much appreciated.
Joe Blow
.45 acp
For .223 I use nothing but Hodgdon Varget. I know it as commonly called "stick" powder. Love it...
Last edited:
meketrefe
.450/400 Nitro Ex
I would love to write a long list of things but I think that most of what you need to do is already in the
reloading section in a sticky.
Safety first so understanding the safety measures and how to keep everything organized ahead of time
and also read some materials regarding all steps from brass selection and preparation to bullet seating and crimping
and how to get a consistent final round.
Make a check list and put it in front of you right above the press. Leave the powder canister out in front of the
charging station or press so you know what powder is in the thrower. Do not mix canisters and take your time.
There are 3 main rules that one should follow all the time and then you should be fine:
1. Measure
2. Measure again
3 when done with the above then verify and measure a bit more.
Assume nothing.
You will be fine. 223 is a forgiving caliber and excellent round to start reloading rifle. You will be grouping like crazy
in no time.
reloading section in a sticky.
Safety first so understanding the safety measures and how to keep everything organized ahead of time
and also read some materials regarding all steps from brass selection and preparation to bullet seating and crimping
and how to get a consistent final round.
Make a check list and put it in front of you right above the press. Leave the powder canister out in front of the
charging station or press so you know what powder is in the thrower. Do not mix canisters and take your time.
There are 3 main rules that one should follow all the time and then you should be fine:
1. Measure
2. Measure again
3 when done with the above then verify and measure a bit more.
Assume nothing.
You will be fine. 223 is a forgiving caliber and excellent round to start reloading rifle. You will be grouping like crazy
in no time.
meketrefe
.450/400 Nitro Ex
@Wildman1024 I forgot from all the garbage in YouTube there is something of value so check out a guy that goes by ammosmith or somethign like that.
He has very good close ups of things and will give some tips even to the most expert reloaders including wildcatters and guys into brass forming like I do.
Let me know if you don't find the threads in the reloading section. Maybe they got lost in an ocean of political posts.
He has very good close ups of things and will give some tips even to the most expert reloaders including wildcatters and guys into brass forming like I do.
Let me know if you don't find the threads in the reloading section. Maybe they got lost in an ocean of political posts.
Wildman1024
.357 mag
I'll take a look. Thanks.
meketrefe
.450/400 Nitro Ex
Sorry I cannot be more involved in the forum. It is crunch time at work but if anything you can always give us a shout. Good luck.
Wildman1024
.357 mag
All good
Wildman1024
.357 mag
So...I am working on setting up my case trimmer. Looks like case length for 223 should be 1.750 with a max OAL of 1.760. It's really hard to get it dialed in perfect. If I am at 1.49-1.51 that should be OK I assume? I'm not going for match grade stuff here.
Do you even need to trim all the time anyways? If you are between 1.750 and 1.760 do you even trim?
Do you even need to trim all the time anyways? If you are between 1.750 and 1.760 do you even trim?
Acer-m14
20×102mm Vulcan
see the case trim max length from your book .. under that a bit your still good.
i reload 270 win and its the same case as 30-06 just a different neck dia for the bullet .. so when i neck down a 30-06 to 270 win is way short
but it works and will take a few reloads to stretch the neck back out for trimming ..
watch your terminology OAL over all length that is loaded with bullet ..
COL and OAL are pretty much the same thing, one is just more specific than the other, but usually refer to the same measurement - Base of the case to the tip of your bullet.
1.750" or 1.760" is the min and max for trimming case length ..
shoot for the middle
Wildman1024
.357 mag
So I have been doing a little reading around the web. Seems like unless the case is greater than 1.755, they do not trim it.
What would be the minimum usable case length? 1.73? 1.74?
Acer-m14
20×102mm Vulcan
@Wildman1024 I would reject any case under the min spec unless you know its good .. unlike the 30-06 to 270 conversion that i do which is a known process and works
what 223 gun you loading for semi .. should crimp neck to bullet , bolt can pass on
what 223 gun you loading for semi .. should crimp neck to bullet , bolt can pass on