thread protector - 315 area

Loworange88

Loworange88

.40 S&W
Messages
199
Reaction score
220
Location
13039
Hey everyone. Is there anyone in the Syracuse area that can permanently fix a thread protector on a barrel for a reasonable price? I'm not sure of the correct process, ie: pin and spot weld, spot weld only, silver solder, or some sort of chemical bond...

Thanks.
 
kev74

kev74

20×102mm Vulcan
Messages
45,608
Reaction score
143,904
Location
Orange Co.
Silver solder + mapp gas torch. You can do it yourself cheaper than paying someone else.
 
kev74

kev74

20×102mm Vulcan
Messages
45,608
Reaction score
143,904
Location
Orange Co.
Loworange88 said:
I thought of attempting this....will the heat from the MAP gas ruin the bluing on the thread protector?
Click to expand...
Not unless you go crazy with the heat.

I used a silver solder / flux paste that comes in a tube. Clean the blue from the threads, put on a little of the paste, assemble, then heat until you see the solder melt and flow a bit.
 
Exonautic

Exonautic

.308 Win
Messages
2,895
Reaction score
2,599
Location
Hell Island
Thread it on and be done with it? Ianal but I doubt anyone is gonna check if it's not something potential nfa material.
 
Acer-m14

Acer-m14

.950 JDJ
Messages
34,602
Reaction score
36,438
Location
Livingston
locktite and snug it up ... they can't use tools to undo it .. if it don't come off by hands .. it's fixed .. FUAC ..

PS .. or just bugger up the threads .. if it can't screw on good to go .. LOL .. @Bullet Guy
 
Robin

Robin

.475 A&M Magnum
Messages
18,649
Reaction score
39,735
Location
Livingston County
There are some silver based solders that will liquify at around 450 deg's F., But if Acer is right, that's the way I would go.
Robin
 
Mosinitis

Mosinitis

.338 Win Mag
Messages
7,643
Reaction score
6,849
Location
NY state
Blue loctite should do it. If needed its bond can be broken without applying heat. I don't recommend applying heat to the barrel if it can be avoided.
NO WELDING!!!!
 
T

Twogunwilly

6.5 Creedmoor
Messages
2,431
Reaction score
3,615
Location
Low Green Mountain foothills
Very simple process, actually written on the labels.
Correct me if I'm wrong but wouldn't an FFL be required to work on somebody's gun?

Man this could be an awesome way to jam up a helpful gun owner just trying to help a stranger on the interwebz :idk:
 
Exonautic

Exonautic

.308 Win
Messages
2,895
Reaction score
2,599
Location
Hell Island
Twogunwilly said:
Very simple process, actually written on the labels.
Correct me if I'm wrong but wouldn't an FFL be required to work on somebody's gun?

Man this could be an awesome way to jam up a helpful gun owner just trying to help a stranger on the interwebz :idk:
Click to expand...
No, anybody can work on anyone's gun. However you can't take possession of it. So I can't have @Loworange88 ship me his gun to throw a thread protector on it. That would require an FFL. But if he drove down to me and I did it with him standing next to me, that's all gtg.
 
spat

spat

.700 Nitro Express
Messages
26,102
Reaction score
54,263
Location
Formerly Geneseo, NY. Now free in AZ
Exonautic said:
No, anybody can work on anyone's gun. However you can't take possession of it. So I can't have @Loworange88 ship me his gun to throw a thread protector on it. That would require an FFL. But if he drove down to me and I did it with him standing next to me, that's all gtg.
Click to expand...
Pretty sure you can't take any money or other compensation either.
 
kev74

kev74

20×102mm Vulcan
Messages
45,608
Reaction score
143,904
Location
Orange Co.
Willjr75 said:
Nope. But why go against ATF regs? Laziness? Is 30 bucks saved worth it?
Click to expand...
It can't hurt, but it might not help.

Reasons not to follow a 20 year old ATF letter...its not doable in a home shop unless you've got a tig welder and know how to use it, high temp solder at 1,100°+ is going to mess with barrel strength and finish, and nobody knows if those mods are going to be kosher for unSafe law compliance.
 
Last edited:
Marine Cpl

Marine Cpl

.577 Tyrannosaur.
Messages
22,054
Reaction score
20,648
Location
Orange County
kev74 said:
It can't hurt, but it might not help.

Reasons not to follow a 20 year old ATF letter...its not doable in a home shop unless you've got a tig welder and know how to use it, high temp solder at 1,100°+ is going to mess with barrel strength and finish, and nobody knows if those mods are going to be kosher for unSafe law compliance.
Click to expand...
Those regs still apply to barrel length so it's still relevant. They even have them in their codes.

As far as not having the tools, one either buys the tools to do the job properly or he sends it away for a Smith to do it if he wants a leg to stand on. That's how I see it. Especially when your freedom is on the line. But one can do what he wants. He can also have a 15.5 inch barrel. He'll just have to answer for it in the off chance he's ever caught and a DA has a bug up his or her ass. That'll cost time and money. Much more than 30 bucks to send it away.

I understand NY doesn't have regs on how to do it but the ATF does. (Especially for barrel length) In the event anyone finds themselves in court, one can say they followed ATF regulations on how to do the job properly. One cannot say the same with blue or red Loctite.

I'd much rather steer the OP to do it the way any professional Smith worth his salt would do it rather than telling him to just use glue and not worry about it.
 
Last edited:
You must log in or register to reply here.
Top