BerettaGuy
.308 Win
Wait for it....... 158-grain wadcutters?
I also have some 357 brass to use.
I also have some 357 brass to use.
Any Idea's for a Recipe for making 38 Spl self defense loads from.......
- Thread starter BerettaGuy
- Start date
ArmedCorgi
.475 A&M Magnum
Cut an "X" into the wadcutter like in the movie "The Bear"?
kev74
20×102mm Vulcan
The 158 grain wad cutters punch nice holes. They should be adequate as-is.
I've heard of people loading them backwards to make a kind of hobo hollow point, but I can't see that working well.
I've heard of people loading them backwards to make a kind of hobo hollow point, but I can't see that working well.
Acer-m14
.950 JDJ
Pinned by TAOFLEDERMAUS
TAOFLEDERMAUS
3 years ago
Honestly, the biggest difference between these and an unaltered bullet was how they expanded. The energy between the bullets would be exactly the same, hence the damage would be the same. Note the difference in expansion at 09:38.
send some wadcutters to Rex for some testing ??
BerettaGuy
.308 Win
I guess my question is, is there a problem if I go over 90 grains of Winchester 231? (5.8 grams) I'm not trying to get into the Reloads in your carry gun are a bad idea legally. It will certainly be used against you in court questions, but in a SHTF situation, I can barter.
I would say that yes, using more than 90 grains of w231 would not be advisable.
kev74
20×102mm Vulcan
Lee gives a max charge of 4.5 grains of Win 231 under a 158 grain lead bullet with a minimum overall length of 1.550".
Lyman gives a max load of 4.0 grains of Win 231 under the same bullet with a minimum OAL of 1.445"
90 grains of 231 (or even 5.8 grains) is likely to give you a hand grenade.
The recipes above are for conventional bullets, not wadcutters. Wadcutters would have a reduced load due to the smaller combustion / expansion area in the case with the more deeply seated bullet.
Lyman gives a max load of 4.0 grains of Win 231 under the same bullet with a minimum OAL of 1.445"
90 grains of 231 (or even 5.8 grains) is likely to give you a hand grenade.
The recipes above are for conventional bullets, not wadcutters. Wadcutters would have a reduced load due to the smaller combustion / expansion area in the case with the more deeply seated bullet.
holdover
.475 A&M Magnum
I have some 357 and 38 Nickle plated range brass to trade. Looking for 223,or 6.5 Creedmoor. Any swaps?
Way back in the day Elmer Keith ran hot 158gr wadcutters for a defensive load. It wouldn't be as good as a hollowpoint but better than round nose FMJs. Frankly with the supply issues we are having, do what you gotta.
Xae289
.223 Rem
I've read several times from various sources that Jim Cirillo from the NYPD Stakeout Squad preferred full wadcutters for their more lethal effect. Having talked to a couple older NYPD detectives, they confirmed that they preferred to carry the full wadcutters in their .38 snubbies over the round-nose stuff. Neither ever had to put them to the test.
No idea about 158 grain wadcutters or .357 brass, but here's data for 148 grainers in .38 brass.
One manual gives me a [3.5 GRAIN START LOAD] of Winchester 231, and a [4.0 GRAIN MAX LOAD] with a velocity range of 869-956 fps. Those velocities seem pretty ambitious given that Hodgdon uses a 7.7" test barrel, which I'm guessing is unvented.
With IMR Trail Boss powder, it lists a [2.0 grain START LOAD] to a [2.3 grain MAX LOAD] with a velocity range of 625-675 fps. Again, I'd expect real velocities to be lower.
I just got dies and about 1000 count 148 gr wadcutters for my .38, so I'm really hoping either of those starting loads are accurate because they'd make for some really economical shooting. I'll probably work up a couple batches with these powders, run them by the chronograph, and post the results. Results will be with a 1-7/8" barreled snubbie.
No idea about 158 grain wadcutters or .357 brass, but here's data for 148 grainers in .38 brass.
One manual gives me a [3.5 GRAIN START LOAD] of Winchester 231, and a [4.0 GRAIN MAX LOAD] with a velocity range of 869-956 fps. Those velocities seem pretty ambitious given that Hodgdon uses a 7.7" test barrel, which I'm guessing is unvented.
With IMR Trail Boss powder, it lists a [2.0 grain START LOAD] to a [2.3 grain MAX LOAD] with a velocity range of 625-675 fps. Again, I'd expect real velocities to be lower.
I just got dies and about 1000 count 148 gr wadcutters for my .38, so I'm really hoping either of those starting loads are accurate because they'd make for some really economical shooting. I'll probably work up a couple batches with these powders, run them by the chronograph, and post the results. Results will be with a 1-7/8" barreled snubbie.
kev74
20×102mm Vulcan
PM on the way.
kev74
20×102mm Vulcan
Its still an accurate load. You just have to work harder for it.
Yea its awesome in the k38, those other 38s will never rival it. So i will use the ammo to practice with the bullseye machine
BerettaGuy
.308 Win
Nice, I use 3.0 in my target loads with 158g
spat
.700 Nitro Express
Ultimate SD loads....
Take your wad cutter bullets, drill a hole in the nose the exact size for a small pistol primer.
Enjoy hollow points from hell......
Note: I do not recommend attempting to defend these in court. It will not go well. But they should have *lots* of "stopping power" in even a lower power cartridge.
Take your wad cutter bullets, drill a hole in the nose the exact size for a small pistol primer.
Enjoy hollow points from hell......
Note: I do not recommend attempting to defend these in court. It will not go well. But they should have *lots* of "stopping power" in even a lower power cartridge.
